| Mileage Correction .Net :: |
| Author |
Message |
mohsinauto
Member
Joined: 25 May 2008
Posts: 58
|
| Posted: Fri Jun 06, 2008 1:01 am Post subject: How to adjust mileage for Hiace 2006 using DIGA-Consult |
 |
|
I have DIGA-Consult or Tacho universal 2007 and I want to adjust mileage for Toyota Hiace 2006.
How can I do it, can anybody help me |
|
| Back to top |
|
 |
Google
|
| Posted: Post subject: Sponsored Link |
|
|
|
|
| Back to top |
|
|
hcip
Senior Member
Joined: 03 Mar 2006
Posts: 150
Location: Brgy. Commonwealth, Quezon City Philippines
|
| Posted: Fri Jun 06, 2008 6:32 am Post subject: Re: How to adjust mileage for Hiace 2006 using DIGA-Consult |
|
|
| mohsinauto wrote: | I have DIGA-Consult or Tacho universal 2007 and I want to adjust mileage for Toyota Hiace 2006.
How can I do it, can anybody help me |
Use SW13 cable or clip
select menu toyota --> Landcruiser --> C66 -- 2002
regards |
|
| Back to top |
|
|
mohsinauto
Member
Joined: 25 May 2008
Posts: 58
|
| Posted: Fri Jun 06, 2008 12:23 pm Post subject: Toyota Hiace 2006 |
|
|
Thank you hcip very much,
I can't find SW13 Cable in my Tacho universal 2007 Kit. Can you show me the picture of this cable SW13 and where to connect the it to cluster?
I attached the pictures of Hiace cluster
Thank you again
mohsinauto@hotmail.com |
|
| Back to top |
|
|
hcip
Senior Member
Joined: 03 Mar 2006
Posts: 150
Location: Brgy. Commonwealth, Quezon City Philippines
|
| Posted: Fri Jun 06, 2008 3:03 pm Post subject: |
|
|
You can use clip if you have no SW 13 cable
SW13 cable is the wire like in your cable in clip
it has pin configuration 1 8 2 7 3 6 4 5
pin 1 is the wire with stripe
 |
|
| Back to top |
|
|
hcip
Senior Member
Joined: 03 Mar 2006
Posts: 150
Location: Brgy. Commonwealth, Quezon City Philippines
|
| Posted: Fri Jun 06, 2008 3:10 pm Post subject: Re: How to adjust mileage for Hiace 2006 using DIGA-Consult |
|
|
Use SW13 cable or clip
select menu toyota --> Landcruiser --> C66 -- 2002
regards[/quote]
Sorry for my mistake
eeprom is 93C56 and not 93C66
select toyota > Land cruiser > S220
regards |
|
| Back to top |
|
|
mohsinauto
Member
Joined: 25 May 2008
Posts: 58
|
| Posted: Fri Jun 06, 2008 5:26 pm Post subject: Toyota Hiace 2006 |
|
|
Thank you very much.
Your explanation is very clear and easy to do but my cluster doesn't look like the photo you sent. It is different, There is no big IC near the EEprom and I can't find these contacts.
Thank you very much |
|
| Back to top |
|
|
mohsinauto
Member
Joined: 25 May 2008
Posts: 58
|
| Posted: Fri Jun 06, 2008 11:15 pm Post subject: Hiace 2006 |
|
|
Yes , it is the same cluster, After I removed the front white cover, it is the same,
But I get 000000 also after soldring the contacts, and also tryed to put the clip directly on the eeprom 93c56. |
|
| Back to top |
|
|
mohsinauto
Member
Joined: 25 May 2008
Posts: 58
|
| Posted: Fri Jun 06, 2008 11:18 pm Post subject: Hiace 2006 |
|
|
Hi,
Yes , it is the same cluster, After I removed the front white cover, it is the same,
But I get 000000 also after soldring the contacts, and also tryed to put the clip directly on the eeprom 93c56.
I didn't unerstand the two red circles and the black circle on the cluster plug? |
|
| Back to top |
|
|
hcip
Senior Member
Joined: 03 Mar 2006
Posts: 150
Location: Brgy. Commonwealth, Quezon City Philippines
|
| Posted: Sat Jun 07, 2008 3:03 pm Post subject: Re: Hiace 2006 |
|
|
| mohsinauto wrote: | Hi,
I didn't unerstand the two red circles and the black circle on the cluster plug? |
The two red circle is positive 12V an black circle is negative side if you want to Power up the cluster to check the KM
Use SW13 cable to read the eeprom
This cluster can read by diga without removing the eeprom
make sure that the pin connections are correct |
|
| Back to top |
|
|
mohsinauto
Member
Joined: 25 May 2008
Posts: 58
|
| Posted: Sat Jun 07, 2008 4:49 pm Post subject: Hiace 2006 |
|
|
Hi hcip,
Thank you for your patient with me. You are a wonderful person. I hope we can be friends and offer such good and excellent help always.
I think now I know my mistake. When I pulled the wires out of the clip I get number 1, 2, 3, 4 right, but 5, 6, 7, ,8 wrong. I just made them opposite. like this 8 7 6 5
Now I can’t try again because I gave the cluster back to the customer, but now I think I know my mistake.
Is soldering these contacts the only way to do it? Can’t I do it by clip? Because I tried to do it by putting the clip on the 93c56 chip but I get the same result. |
|
| Back to top |
|
|
Clusterslaststand
Senior Member
Joined: 23 May 2008
Posts: 123
|
| Posted: Sat Jun 07, 2008 5:23 pm Post subject: |
|
|
It should work with the clip.
Maybe the soldering on the wires of the clip was bad or the legs of the eeprom where not clean.
Use fibreglass pen and pcb cleaner to clean legs next time. |
|
| Back to top |
|
|
mohsinauto
Member
Joined: 25 May 2008
Posts: 58
|
| Posted: Sat Jun 07, 2008 10:19 pm Post subject: Hiace |
|
|
Thank you very much
and I don't have to change the sequence of the wires in the clip? Because I know that Toyota Yaris 2003 I should change the sequence of the wires in the clip. |
|
| Back to top |
|
|
hcip
Senior Member
Joined: 03 Mar 2006
Posts: 150
Location: Brgy. Commonwealth, Quezon City Philippines
|
| Posted: Sun Jun 08, 2008 1:16 am Post subject: Re: Hiace 2006 |
|
|
| mohsinauto wrote: |
Is soldering these contacts the only way to do it? Can’t I do it by clip? Because I tried to do it by putting the clip on the 93c56 chip but I get the same result. |
You can clip the eeprom but you have to remove the wax on it
it is better to solder it on solder pad
if you are in good soldering job, next time that some guys opened its
cluster they will thinking that it still a virgin becaused you have not touched the wax on eeprom
Regards |
|
| Back to top |
|
|
Bannybasher
Senior Member
Joined: 13 May 2008
Posts: 212
|
| Posted: Sun Jun 08, 2008 7:47 pm Post subject: |
|
|
if you need to remove the laquar use nitromoors . it works a treat. a little bit on a ear bud, leave it to soak for a few minutes.
Rub off with a fibre glass pen . easy.
A point about the yaris with rotated pins:
if your 95 board have a port 4, then use that port
it saves time moving all the pins two to the left. |
|
| Back to top |
|
|
|
