| Mileage Correction .Net :: |
| Author |
Message |
ahmadiga
Junior member
Joined: 13 Feb 2008
Posts: 11
Location: Nigeria
|
| Posted: Sat Feb 23, 2008 1:10 pm Post subject: I,m in problem,I need help. Accord 2008 |
 |
|
hello
Please i have a problem i need technical asistance.someone gave me accord 2008 dash to correct, before doing anything i post a question in this forum but no one seem to have done accord 2008, then i decided to open the cluster and do it and i read the eeprom but it was giving me wrong numbers.then i decided to return it back but when i return it back it refuse to work the odometer is blank,the fuel gauge,tachometer,speedometer and temp gauge stop working. Please i need your assistance i suspect the processor and i don't know where to find it,please if you know the cause of this problem help me out .i have 15 years electronic engineering experience,if you can help me with the parts i will pay you and i believe i can fix it because in my country there's no cluster spareparts. this is the number of the processor 6432638M58FV and the odometer is in KM. Please help me out.
Regards
Ahmadiga |
|
| Back to top |
|
 |
Google
|
| Posted: Post subject: Sponsored Link |
|
|
|
|
| Back to top |
|
|
Edmond
Junior member
Joined: 06 May 2006
Posts: 17
|
| Posted: Sat Feb 23, 2008 4:11 pm Post subject: |
|
|
Did you save the dump when you read the eeprom?
Did you still try to programme it when even it show wrong numbers?
Did you check what type of chip you reading?
Did you de-solder off the board to read the chip? |
|
| Back to top |
|
|
ahmadiga
Junior member
Joined: 13 Feb 2008
Posts: 11
Location: Nigeria
|
| Posted: Sat Feb 23, 2008 6:30 pm Post subject: Accord 2008 |
|
|
Hi
I did not save the dump,i did not programme the chip, i only read the chip without knowing the real number of the chip i select diferent honda models with my tacho dash prog. and no one that match with the original numbers. I did not remove the pointer from the dash because i'm afraid i only use a long needle attach to my ohmmeter and insert it between the board and the front plastic of the cluster to know the pins solder connections,and i got it. But i did not trace the crystal connection, And about soldering i did it well and i did not remove the chip.
Regards.
Ahmadiga |
|
| Back to top |
|
|
Edmond
Junior member
Joined: 06 May 2006
Posts: 17
|
| Posted: Sat Feb 23, 2008 10:15 pm Post subject: |
|
|
I do not like to elaborate your impulses. The most concern
is the #5 & #8 connection. If it's connected in the wrong
spot or reverse connection, anything unpleasand could
happen. |
|
| Back to top |
|
|
ahmadiga
Junior member
Joined: 13 Feb 2008
Posts: 11
Location: Nigeria
|
| Posted: Sat Feb 23, 2008 11:17 pm Post subject: Accord 2008 Solution |
|
|
Hi
The connection of pin 5 is ground and the connection of pin 8 is +5v everything is connected normal, if you have any idea of what may cause
that problem i will be glad to hear from you.
Wishyou Nice Weekend.
Ahmadiga |
|
| Back to top |
|
|
hcip
Senior Member
Joined: 03 Mar 2006
Posts: 149
Location: Brgy. Commonwealth, Quezon City Philippines
|
| Posted: Sun Feb 24, 2008 7:23 am Post subject: Re: Accord 2008 Solution |
|
|
| ahmadiga wrote: | Hi
The connection of pin 5 is ground and the connection of pin 8 is +5v everything is connected normal, if you have any idea of what may cause
that problem i will be glad to hear from you.
Wishyou Nice Weekend.
Ahmadiga |
Hello
If you have interchange the connections of data out pin & data in pin,
This will cause to erase the chip, even you are in reading mode
regards |
|
| Back to top |
|
|
ahmadiga
Junior member
Joined: 13 Feb 2008
Posts: 11
Location: Nigeria
|
| Posted: Sun Feb 24, 2008 9:54 am Post subject: Accord 2008 |
|
|
Hi
Thanks for your assistance,did you have dumb for the chip. please advice me what to do.
Regards |
|
| Back to top |
|
|
hcip
Senior Member
Joined: 03 Mar 2006
Posts: 149
Location: Brgy. Commonwealth, Quezon City Philippines
|
| Posted: Sun Feb 24, 2008 10:53 am Post subject: Re: Accord 2008 |
|
|
| ahmadiga wrote: | Hi
Thanks for your assistance,did you have dumb for the chip. please advice me what to do.
Regards |
sorry I have no dump for this car
but you can ask some member here
http://diagcar.exofire.net/phpBB3/
I hope they have
regards |
|
| Back to top |
|
|
Edmond
Junior member
Joined: 06 May 2006
Posts: 17
|
| Posted: Mon Feb 25, 2008 1:41 am Post subject: Re: Accord 2008 Solution |
|
|
| hcip wrote: |
Hello
If you have interchange the connections of data out pin & data in pin,
This will cause to erase the chip, even you are in reading mode
regards |
I don't think so.
To almadiga,
If the #5 & #8 connection are confirm correct. Go to check what you might
have loosen when you tried to probe the continuity to the back of the
board for your connection. Power-up your cluster on the bench. You might
be able to check the 5v+ & 5v- spots where you connect your #5 & #8. |
|
| Back to top |
|
|
samuel
New member
Joined: 02 Feb 2007
Posts: 4
|
| Posted: Sun Jul 27, 2008 6:49 pm Post subject: 08 accord |
|
|
| just wanted to know did you fugure out 08 honda accord |
|
| Back to top |
|
|
|
